​​​​

Radio Controlled Rocket Glider Kits

Delta X-15-3 Rocket Glider Kit

This is an  X-15-3 Delta configuration style that was proposed in the 60's.   The photos show the Ikarus kit but the instructions are identical and only the tail and wingtip shapes are different.  It has a high mounted delta wing with a light wing loading giving it a very nice glide and easy/stable boost.  It comes with a plastic nose cone and bt-80 tubing for the body and depron wing and tail surfaces.  Construction is very simple and takes about an hour.  You will need two 10 gram type servo, two 18-24" servo extensions, a receiver, and a small 250-500mah single cell lipo battery.  You will need a transmitter with delta or elevon mixing.  I used the standard X-15 markings from stickershock23.

Please refer to the notes on items needed for completion and flying, then read the instructions completely before starting assembly.  The assembly photos are for general reference but may not include every step in the manual. 

​CG location for rocket flight 14 5/8" forward from the TE of the wing

(Due to the CG location, and the fact that the equipment is mounted inside a body tube with no cooling airflow, it would be difficult to attach a battery and speed control in an optimum/accessable location, so it is not recommended to fly this using the electric adapter)





Welcome to the world of rocket boosted radio control gliders.  This is not a model for a novice RC pilot, but anyone who is comfortable with RC flying of a medium speed model should be fine.  Read through the instructions, look at the photos and be sure you understand the step before commiting to cutting or glue.

Delta X-15-3 Rocket glider instructions

Identify all pieces, the kit should contain:

1  wing  taped together


2 wing spars(carbon fiber)


2 pushrods


3 Vertical Stabilizers


2 Foam wing reinforcing strips


2 foam motor mount reinforcing strips


2 Body Tubes


Motor mount


Paper canopy

Velcro(for battery and rx/bec attachment)

2 Rail buttons or 1 Launch lug

3M blenderm tape

Lead weight

Spare depron

Optional(if ordered):

Electric motor adapter

Notes before starting:

Reference to CA+ means foam safe CA+, normal CA+ will melt the foam!  Normally you need to use accelerator to get the CA to set on the foam since there is nothing for it to soak into and activate.

You may use 220-320 grit sandpaper and a sanding block to slightly round the edges of the foam if you prefer that look.  It will not markedly impact the flight performance either way.  Be very careful and use a light touch, it is very easy to catch the foam on the edge of the paper and tear the foam.  Do any sanding before assembly.

Epoxy is not needed in this model.  Weight is critical and the model is designed for the thrust and flight loads.  Weight in the rear end is bad and will require additional weight in the front of the model.



Assembly:

  1. Unfold the  wing and glue the tape joints using CA+ and accelerator, make sure it is flat
  2. Glue the two wing spars in the pre-slotted areas on the bottom of the wing with CA+ and then tape over with the included blenderm tape.
  3. Body Tubes.   One of the tubes has a line that does not go all the way to the front, that is the forward tube, we'll use that later.  The other tube will have a line inside the tube on one end, that is the rear tube and the inside line is for the motor tube alignment.   
  4. Glue the the coupler halfway into the rear tube into the end marked "coupler". Use glue sparingly, you don't need a lot of strength here as the wing will support the tubes as well.  
  5. If using rail buttons, use a tool or drill make holes in the tube at the  "x" marked "RB".  Insert a T nut into each hole from the inside and then install the rail button and screw.  You don't need to tighten them down really tight, just enough to hold them in place.  In early models there is a single rail button mark on each body tube, on later models the two rail buttons locations are marked on the rear tube only.
  6. Glue the front tube to the rear tube at the coupler, make sure to keep the line on outside of the two tubes aligned.
  7. Insert the two pushrods into the outermost hole in the control horn.  Do this from the inboard side of the horn, do it now because it is difficult to do this once the wing is glued to the tube.  You will need to twist the pushrod to get it to go into the hole, be careful and don't poke your finger, go slowly so that it fits snugly.
  8. Lay the wing upside down on a flat surface.  Using CA+ foam safe glue glue the body tube to the wing.  Use the pencil marks on the body tube as a guide.  You can use the vertical stab cutout on the wing to see that the rear is aligned and use the front of the wing as well.  Make sure the tube is not rolled to one side or the other.
  9. Apply CA+ foam safe glue to one of the reinforcing strips and glue one on each side of the wing/body tube joint.  The reinforcing strip should align with the rear of the model but won't go all the way to the front of the wing.  This piece is there to give more gluing surface to the wing/body tube.  If you push in too hard on these strips it can cause the body tube to rotate slightly, so pay attention. Once they are in place put a fillet of CA+ on both the wing and body tube joints.
  10. Glue the motor tube at the top of the body tube right underneath the wing and aligned with the end of the body tube.  The model is upside down now so it will be the at the bottom of the tube in this orientation. Make sure the motor tube is aligned straight with the body tube.  There are no centering rings needed or desired because you may need to reach wiring or weight at the rear of the model.  The motor tube hook is only taped on one side, you want to be sure you don't glue to the tape or hook, this is done so that you can glue the paper motor tube directly to the body tube without the tape in the way. 
  11. Glue the two short reinforcing strips on either side of the motor tube and add a fillet of CA+ to help support the motor tube.
  12. Glue the vertical stab to the wing using the tab.  Make sure it is 90 degrees to the wing, is straight and reinforce with a slight fillet.
  13. Glue two wing tips to the wing, the larger suface points "up"  Make sure they are perpendicular to the wing and put a small fillet to reinforce the joint.
  14. If you are using a launch lug I recommend putting it at the wing/body tube joint so that it will clear any wiring/servo placement, or on the side of the tube about midway down.
  15. Cut out the canopy.  Fold the canopy at each black line, fold so that the black lines will be in the underside of the canopy.  Glue the tab at the front to form the shape.  Once complete glue the canopy to the top of the model on the nose cone.Trim as needed to fit.


The basic construction is now complete.


Radio Installation

Note:  Your radio needs to be configured for Delta mixing, this means that the servo arms will move the same direction during elevator stick movement and opposite for aileron stick movement.  Connect your servos to the receiver one in the aileron connection and one on the elevator connection and apply power.   Use a servo arm at least 9/16” long and with holes small enough that there won’t be slop with the pushrod wire when installed.  I use the hole furthest out on the servo arm, to maximize movement. On some servos there are a long two-ended servo arm, you can trim off one end if needed to get sufficient length.   Zero out any trim settings on the transmitter. The model once the motor has burned out is nose heavy and flying wings lose pitch authority when nose heavy so you want as much up elevator travel for trim/flare as possible.


  • Connect a servo to each pushrod, the servo wire should be closest to the center and the output shaft is outboard toward the wing tip.   If the wire is too tight, you can use twist an exacto knife in the servo arm hole to make it larger, but be careful and do not make it too large.  Once connected, tape each servo in place so that the control surfaces are centered.  Flip the model right side up and look at it from the rear.  Moving the transmitter stick back(up elevator) should move both elevons up.  Moving the transmitter stick to the right should move the right elevon up and the left elevon down.   If you can’t get the servo reversing to give you the right polarity try swapping aileron/elevator inputs to the receiver or turning the servos over and swapping the servo arms to the other side of the output shaft.  If that is correct, continue..
  • Flip the model upside down and supported.  The servos may be attached to the model using double back servo mounting tape(not included) or by directly gluing the servo to the wing with CA+ or a small amount of epoxy.  Double back servo tape can loosen over time and with exposure to heat, I prefer to glue the servo in place.  With the radio still on, put a small amount of glue on the servo, being careful not to get any near the output shaft. And set it in place on the model keeping the control surface centered.  Do the same to the other side.  Make sure the glue is set before continuing.  The servo and pushrod should be at 90 degrees to the hinge line so that it moves easily and fully. 
  • Flip the model back right side up.  Make sure the control surfaces are centered, use trims if needed.  Now measure the control surface movement.  Full elevator movement should be 1” in each direction, aileron movement should be 3/4" in either direction.  Since the model will be nose heavy, extra elevon movement helps to give sufficient authority during glide. 
  • If you have a flap/elevator mix you can program up elevator to a switch setting.  The model needs approximately  1/4” of up elevon during glide. If you can’t set the up elevator trim to a switch on your radio you’ll have to manually put in boost and glide trim which is hard to do while flying the model.
  • Attach a 24" servo extension to each servo.
  • Make a slot in the bottom of the wing/fuselage and pass the wires through to the inside and toward the front.
  • Attach the servo wires to the receiver and make sure they are going the right direction.  Tape down the servo wires to the wing and tape over the slot in the body tube.
  • Use the included Velcro to attach the receiver 1.5" from the front of the body tube. This allows you to be able to remove and replace the receiver if needed for repairs or for removing the servo wires. I attached the battery inside  nose cone on the shoulder.
  • Insert your heaviest loaded rocket motor into the motor mount
  • Support the model at the balance point indicated for boost.  I use two pencils with the eraser pointed up and held in place with a small hand vice.  Place the model upside down on the pencil erasers on the balance point indicated in the kit spec sheet.  Use the included lead weight at the front or back of the model to balance it.
  • Do not try to fly the model with it balancing it behind this point.  The adage is, a nose heavy model flies poorly, a tail heavy model flies once. 
  • If you paint the model, make sure you test it on scrap foam first.
  • If you are going to paint the model, you can mask off the servos.  Make sure no paint will get on the servo output arm.  Make sure to test the paint on a scrap piece first to ensure it won’t melt the foam.  I use Model Master(testors) or testors small rattle cans for painting directly on the foam. 
  • I used  vinyl for the trim colors on my model.  With the vinyl from stickershock23 it helps once applied to use a hair dryer on hot to soften the material and then push it down onto the model with a towel.  It helps it confirm and stick much better, especially on painted surfaces.  Use a silver sharpie pen for panel lines if desired.
  • Re-install the receiver and battery


Flying:  See the Instruction/Information link at the top for flying instructions  Be ready on the first few flights to keep the model straight till you have the trims set perfectly for boost and glide.